FREE Electrical Safety Fundamental Basic and tips PDF

The most apparent requirements in determining unsafe equipment are related to the exisitence of the power supply, the types, locations and conditions of the wiring in use, and the existence of the number of wall outlets or ceiling fixtures required by the PEC and NEC, and their condition. In making investigations of unsafe equipment, these pdf ebook will serves as useful guides you can download it freely.



Wiring Regulations free ebook
plays a key role in the electrical installation industry in terms of standards and safety and is known for its independent and trusted voice in this sector.


ELECTRICAL SAFETY HAZARDS AWARENESS
This guide should be used by instructors to supplement the non-electrical worker training module presentation.


BASIC ELECTRICAL SAFETY
The concepts discussed herein are intended to provide explanation and clarification of basic electrical safety for individuals who have little or limited training or familiarity with the field of electricity. Basically, there are two kinds of electricity - static stationary and dynamic moving. This module is about dynamic electricity because that is the kind commonly put to use.


Electrical Safety
Statutes and Regulations,Alaska Department of Labor After the American National Standards Institute approves a new, published edition of the National Electrical Code or a new, published edition of the National Electrical Safety Code, the Department of Labor and Workforce Development may, by regulation, adopt the most recent codes to constitute the minimum electrical safety standards of the state.


Fundamentals of Electrical Safety
It is important to note that all electrical systems must be properly maintained, so as to reasonably prevent danger of electric contacts. Electrical safety is not exclusively defined by the prudent conduct of individuals in the presence of energized objects. A sensible attitude toward electrical equipment may only prevent direct contact, that is, an accidental contact with parts normally live (e.g., energized conductors, terminals, bus bars inside of equipment, etc.

Basic Electricity Definition and Engineering Terms

Basic Electrical Engineering Or Electricity Definition.
Electricity and Magnetism free ebook

source

Ampere
Unit used in measuring intensity of flow of electricity. Symbol for it is "I".

Alternating Current(AC)
Electric current reversing its direction of flow at regular intervals. For example, it would alternate sixty times every second in a sixty cytle system. This  type of current is commonly found in homes.

Bare Conductor
Wire or cable with no insulation or covering


Current
Flow of electricity through a circuit; either AC or DC.


Circuit
Flow of electricity through two or more wires from the supply source to one or more outlets and back to the source.


Circuit Breaker
Safety device used to break the flow of electricity by opening the circuit automatically in the event of overloading, or used to open or close it manually.


Conductor
Any substance capable of conveying an electric current, in the home, copper wire is usually used.


Covered Conductor
WIre or cable covered with one or more layers of insulation.

Conductor Gauge
Numerical system used to label electric conductor sizes, given in American Wire Gauge(AWG) or square millimeters diamter.


Cable
Conductor insulated from one another.


Direct Current(DC)
Electric current  flowing in one direction. This type of current is commonly found in industries.


Electricity
Energy used to run household appliances and industrial machinery; can produce light, sound, heat and numerous other uses.


Frequency
The number of periods per unit time stated in cycles per seconds or Hertz. For alternating current power lines, the most widely used frequencies are 60 and 50 Hertz.

Fuse
Safety device that cuts off the flow of electricity when the current flowing through the fuse exceeds its rated capacity.


Ground
To connect with the earth as to ground an electric wire directly to the earth or indirectly through a water pipe or some other conductor. Usually a green colored wire is used for grounding the whole electrical system to the earth. A white wire is usually to ground individual electrical components of the whole system.


Impedance
A measure of the complex resistive and reactive attributes of a component in an alternating current circuit

Insulator
Material that will not permit the passage of electricity.


Neutral Wire
Third wire in a three wire distribution circuit, it is usually white or light gray and is connected to the ground.


Resistance
Restricts the flow of current; Unit of resistance is Ohm. The more resistance, the less the current flows.


Service
Conductor and equipment for delivering energy from the electricity supply system to the wiring system of the premises.

Service Drop
Overhead service connectors from the last pole or other aerial support to and including the splices, it any, connecting to the service entrance conductors at  the building or ther structure.


Service Panel
Main panel or cabinet through which electricity is brought to building and distributed. It contains the main disconnect switch and fuses or circuit breakers.


Short Circuit
Break in the flow of electricity due to evercurrent resulting from a fault of negligible impedance between live conductors having a difference in potential under norma operation condition.


Voltage Drop
Voltage loss when wires carry current. The longer the cord, the greater the voltage drop.


Volt
Unit for measuring electrical pressure or force, known as electromotive force. Symbol for it is "E" or "V".


Wires
Conductors carrying the electric current or power to the load; usually black or red.


Watts
Unit of electric power. the formula is Volts time Amperes equals watts

Puzzle: Basic electrical terms
Basic electrical terms cross word puzzle


Links on Electrical Formulas
Links On Free download Electrical Engineering Ebooks